Hot

SuperFine Metallic Finish

 1,210 4,625

SKU: N/A Categories: , ,
Clear
View cart

Description

Size: Gallon (3.64 Ltr), Quarter (0.91 Ltr)

SuperFine Metallic Finish is a protective and decorative finish based on selected aluminium paste and a special binder. It gives a sparkling and lustrous finish as well as extreme protection against water, rust and dust.

Surface Preparation:

Pre-primed or on smooth surfaces. Ensure that surface is clean, dry and free from rust, grease, oil and other contamination.

    • Extra coverage
    • Smooth finish
    • Better Flow

Additional information

Size

Gallon (3.64 Ltr), Quarter (0.91 Ltr)

Shade

Sparking Silver 6000, Shiny Green 6001, Deep Green 6008, Champagne 6002, Copper 6003, Black 6009, Ocean Blue 6004, Blue 6010, Violet 6011, Gold Dust 6005, Brown Sheen 6006, Maroon 6007, SkyBlue 6012

Surface Preparation

Preparation of the surface is the most important step in painting and greatly affects the life and appearance of paint. SuperFine Metallic Finish should be applied following the priming. For smoothing out rough surfaces or where the color of finish has changed appreciably, the use of an undercoat is recommended. For maximum durability, apply SuperFine Metallic Finish Paint directly to primer. Previously unpainted surfaces must be thoroughly cleaned before painting. Rust, Mill Scale, Oil, Dust and Grease may be removed by wire brushing, abrasive paper or white spirit. Old work, in a bad condition (blistered, flaked, cracked, or powdery must be burnt off or stripped with paint remover. After cleaning apply one coat of SuperFine Undercoat and on drying apply two coats of SuperFine Metallic Finish Paint. For wood all knots and resinous patches should be treated. In case of bright and new metal surfaces such as Galvanized Iron or Aluminum rub it down with fine sandpaper and clean with white spirit so that paint may not flake off.

Thinning:

Ideally, thin 4 litres of SuperFine Weather Power with 2-3 litres of clear water. However, high-porosity surfaces will require more thinning than low-porosity surfaces.

Application

Please stir thoroughly before applying to ensure even pigmentation. Thin it down with good quality white spirit to desired application viscosity for brushing & spray. Apply two coats of SuperFine Metallic Finish for best results. Between coats allow 12 to 18 hours under normal weather conditions.

Tips For Safety, Economy and Environmental Protection

Keep the paint away from sources of ignition and avoid smoking. Where the painting is in progress ensure adequate ventilation. Do not breathe vapours,use of suitable respiratory equipment is highly recommended. Keep paint container air tight after use and store in a shady & dry place. To save the unused paint for longer period of time,replace the lid firmly and invert the can for few seconds to seal the lid. It will help to prevent skinning. Rinse with plenty of water in case of eye contact and seek medical advice. Use white spirit,turpentine oil or skin cleanser to remove splashes from skin. Scrape excess paint out of brushes and rollers before cleaning. Wash all equipment immediately after use with white spirit or turpentine oil. Shake excess liquid out after washing and then wrap them in a piece of clean cloth. Doing so will revive your brushes back to original. Do not dispose-off excess paint or paint waste into drains or watercourses, disposal should be done in accordance with the environmental regulations.

 

Main Uses Suitable for interior and exterior all metal, wood, plaster, brick and concrete surfaces.
Colour Range Please refer to standard Colour Card.
Covering Capacity 14-17 m²/litre per coat.
Application Brush or Roller
Drying Time Surface Dry: 3 hours, Recoat ability 12-18 hours (Depending on the Humidity & Temperature)
Packaging Gallon (3.64 Ltr), Quarter (0.91 Ltr)

Gobis Color Collection