Saver Series Synthetic Enamel
₨ 250 – ₨ 2,950
- Description
- Additional information
- Technical Data Sheet
- Color Shades
Description
Capital Chemical Industries Synthetic Enamel is high gloss paint with beautiful colors. It provides the tough smooth film with excellent flow and leveling properties. It is based on alkyd resin with high color fastness pigments and specialty additives. It exhibits good resistance against alkali and mild chemical fumes attack. Recommended for wood and metal surfaces.
- Non Yellowing
- Tough & Flexible
- Brilliant High Gloss
- Excellent Durability
- Good Water Resistance
- High gloss
Additional information
| Size | Gallon (3.64Ltr ), Quarter ( 0.91Ltr), Dabbi (0.25Ltr) |
|---|---|
| Shades | Off White 1001, Cream 1002, Diyar 1003, Pale Cream 1004, Beige 1005, Golden Yellow 1006, Ash White 1007, Champagne 1008, Dark Brown 1009, Signal Red 1010, Golden Brown 1011, Red Oxide 1012, Light Grey 1013, Smoke Grey 1014, Light Blue 1016, vivid Blue 1017, Emerald 1019 |
Surface Preparation
Preparation of the surface is the most important step in painting and greatly affects the life and appearance of the paint. Saver Series Synthetic Enamel should be applied following the priming. For smoothing out rough surfaces or where the color of the finish has changed appreciably, the use of an undercoat is recommended. For maximum durability apply Saver Series Synthetic Enamel directly to primer. Previously unpainted surfaces must be thoroughly cleaned before painting. Rust, Mill Scale, Oil, Dust and Grease may be removed by wire brushing, abrasive paper or white spirit. Old work, in its bad condition (blistered, flaked, cracked, or powdery) must be burnt off or stripped with paint remover. After cleaning apply one coat of Saver Series Undercoat and on drying apply two coats of Saver Series Synthetic Enamel. For wood all knots and resinous patches should be treated. In case of bright and new metal surfaces such as Galvanized Iron or Aluminum rub it down with fine sandpaper and clean with white spirit so that paint may not flake off.
Application
Please stir thoroughly before applying to ensure even pigmentation. Thin it down with good quality white spirit to desired application viscosity for brushing & spray application. Apply two coats of Saver Series High Gloss Synthetic Enamel for best results. Allow 12 to 18 hours between coats under normal weather conditions.
Tips For Safety, Economy and Environmental Protection
Keep the paint away from sources of ignition and avoid smoking. Where the painting is in progress ensure adequate ventilation. Do not breathe vapors, use of suitable respiratory equipment is highly recommended. Keep the paint container airtight after use and store it in a shady & dry place. To save the unused paint for a longer period of time, replace the lid firmly and invert the can for a few seconds to seal the lid. It will help to prevent skinning. Rinse with plenty of water in case of eye contact and seek medical advice. Use white spirit, turpentine oil or skin cleanser to remove splashes from the skin. Scrape excess paint out of brushes and rollers before cleaning. Wash all equipment immediately after use with white spirit or turpentine oil. Shake excess liquid out after washing and then wrap them in a piece of clean cloth. Doing so will revive your brushes back to the original. Do not dispose-off excess paint or paint waste into drains or watercourses, disposal should be done in accordance with the environmental regulations.
| Main Uses | Suitable for interior and exterior of all metal, wood, plaster, brick, asbestos and concrete surfaces. Please refer to the standard Colour Card. |
| Covering Capacity | 14-17 m²/Liter per Coat |
| Drying Time | Surface Dry: 3 Hours, Recoat ability 12-18 hours |
| Packaging | 3.64 Liters 0.91 Liters 0.25 Liters |
